New: cFosSpeed v9.0 now with smarter prioritization!
The new light and heavy traffic classification allows prioritization regardless of the L7 protocol. New prioritization for re-used HTTP connections. Better detection of game and other light traffic for unknown protocols. Also improved classification of bulk traffic.
Megjelent a 9-es verzió!!!!!
Új Trial Reset-ért a testem
Sziasztok!
Nem annyira értek a programhoz, de nekem a kapcsolatok száma a Cfos szerint 200tól majdnem 300 között ingadozik. Nem sok egy kicsit?
Nem ertem miert nem lehet ezt az olcso szoftvert megvenni. Raadasul orokervenyu a licensz, nem ugy mint a virusirto programoknal. Karacsonyi akciokban altalaban 1999ft-ra szoktak csokkenteni az arat. Ezert a penzert a program szerintem ajandek, olyankor kell megvenni.
Mas: Es igen vegre nincs a rettegett blue screen hiba, ami nalam torrentezes es bongeszes kozben szokott elojonni, mar evek ota. A telepites is sokkal kenyelmesebb lett az olyan gepeken is, ahol nincs router es az ADSL modem bridge modban van.
Mar ez is nagy ajandek, hat meg a tobbi ujitas.
cFosSpeed 7.00 build 1901 -- 8-Nov-2011
* Added manual priorisation for connections, i.e. you can set connections to a desired class based on their addresses, l7-protocols or programs. Use the "spd prio" (or prioritize or prioritise) command to set the prio on the command line:
Help says: prioritise tcp prioritise udp prioritise prot prioritise prog , , and may contain '?' and '*' wildcards. examples: prioritise tcp 192.168.8.204:52437 194.95.249.23:80 default prioritise udp 192.168.8.204:* 208.67.222.222:53 high prioritise prot *BULK low prioritise prog utorrent.exe lowest
An upcoming version will have a GUI to set priorities.
* cFosSpeed now has class delay management: this regulates the delay of each traffic class (which is user configurable) based on the amount of traffic in the class in comparison to other classes.
Example: if you have a lot of traffic in your 'low' class and your 'high' class traffic doesn't get enough bandwidth, cFosSpeed will introduce some delay for the 'low' class, so it sends less rapidly and your 'high' class streams get some additional performance.
This should greatly help heavy downloaders like torrent users.
* cFosSpeed will now actively slow down the rx-speed of download streams if they are prioritised lower than other streams which run at the same time. In other words: if you are watching a video stream in your brower (high prio) and downloading at the same time (low prio), cFosSpeed will slow down the downloads to make sure you get enough bandwidth for the the video. But if the video is stopped, all bandwidth is again available for the downloads.
This can be switched off by "spd gset throttle_fast 0". Default is on.
"spd classes" and "spd cons -wquot" et al. show a column named "wquot", which is a quotient that shows how fast a stream resp. class is in comparision to how fast it should be. E.g. a quotient of 1.00 means perfect, 1.5 means 50% too fast, 0.8 means 20% too slow.
! To comply with the Windows design guides, cFosSpeed now stores all global and Traffic Shaping related data in \ProgramData\cFos\cFosSpeed directory. All user specific data, like selected language and skins, are stored in \Users\\Appdata\Local\cFos\cFosSpeed.
! The -weight class parameter that is specified in the default settings does now specify the weight of all rx-streams in a class and no longer the weight of a single stream. This helps to keep fast sending streams of low priority (like P2P) slower and higher prio streams faster. A exacter regulation is still in development.
* Added On-the-fly prioritization. The "current connections" dialog now has the option to prioritize a connection, protocol or program temporary or easily add it to the prioritization scheme. Just click on a connection to change its priority. In many cases it will be easier to use this dialog than the normal program and protocol prioritization dialogs. So, for example, while you work/play on your computer and notice a certain connection uses too much bandwidth, you can click it and reduce its priority without changing the general prioritization system.
+ You can now undo the change of priority by using a "spd prio none" command (i.e. by specifying a command with the class name "none"). The class is then reset to the value before the setting.
Only classes that are no longer 'idle' or 'working' can be changed in their priority. Otherwise, they are not in use anyway, since 'idle' or 'working' are only set on fresh connections were the priority could not yet been determined.
+ Added filter expression -manual. It's true for packets on connections that have been manually changed in their priority.
+ The "spd perf" setting is now automatically saved.
+ Added Indonesian & British English language. That makes a total of 32 languages supported. Even more languages are downloadable from our web site, here: http://www.cfos.de/speed/documentation/lang.htm
+ The L7 detector now recognizes Bittorrent uTP.
+ -class rule works now for UDP connections as well.
+ "spd classes" command shows stats for all classes in table form.
+ Added -delay parameter for classes. With this you can make sure packets in that class are sent only after a minimum delay time in the queue. That is, -delay cann add some ADDITIONAL delay for packets. By default, all delays are set to 0, i.e. no additional delays are introduced.
+ Added -class filter expression. This allows filtering after the class of a TCP stream, i.e. you could use the filter "-tx -higher -class lower -c lower" to filter out all TCP ACKs of streams that are classified as lower.
+ The program and protocol prioritization dialogs now have a button to restore the prioritization settings to their default values.
+ The program prioritization dialog now allows you to suggest a newly added program to the cFos team, so we can include it in future releases.
+ Changed the look of the current connections dialog. It also now has a "Freeze" button to stop periodical update of the current connections.
+ Speeded protocol and program prioritization dialogs. This also fixes the bug where IE9 causes page display problems when switching to the games section.
+ Skins now support an x- and y- positioning offset. By specifying x_ofs= and y_ofs= in the [all] section of the skin .INI you can move the skin's default position by pixels to the right and pixels to the bottom. This is useful, if the skins have shadows.
+ Auto-hide on fullscreen now also works after you opened/closed the window manually. However, if you turn off auto-open/auto-hide Auto-hide on fullscreen is also deactivated.
+ Due to popular demand, we added an option to lock the window position to the window settings sub-menu.
+ Added Layer-7 stream detection for VLC and Media Player Classic.
+ From now on, installation archives contain both x86 and x64 flavours of cFosSpeed ("fat" archives). The right Setup is started automatically. Furthermore, the archives are packed with LZX, resulting in a higher compression ratio.
- Status window auto-arrange is now turned off when you manually move the status window.
- Added "spd echo ..." command that just echos the text to the trace file and console.
x Fixed the 2 window problem and disabled line calibration / send test pings in cfosspeed context menu.
x Fixed several bugs in the Online Budget/Counter dialogs.
x Fixed truncated l7-protocol names in connection overview.
x Fixed a crash. Thanks to Norbert Paradowski for dump file.
x When you press the freeze button in the current connections dialog and then click on one of the sorter tabs, the current connections are still refreshed and sorted.
x Fixed a long-standing bug, where the status window would disappear after stand-by/wake up.
x Fixed a bug where newer dialog html files would not overwrite the old ones during an update installation.
x Fixed a bug that caused the driver not to load sometimes after booting.
x If a ping_dest has been set by the user we accept ping replies ("pongs") to any TTL. Otherwise, only ping replies to TTLs 2-4 are accepted. Thanks to tomtores for inspiration.
x Fixed a rare bluscreen.
x Added check against NULL pointer in Windows 7 mobile broadband driver status messages. Thanks to marmal for bug report and dump file.
Így van ! Egyszer írtam nekik hogy szerintem hibát okoz nálam a program, és már szinte zavaró volt hogy mennyi emailt kaptam a hiba okának felderítése érdekében. Aztán késõbb már bántam is hogy írtam nekik és feleslegesen fárasztottam õket, mert tápegységhiba volt.
En megvettem mind kettot, mert sajnalattal lattam, hogy a Cfos fejleszteset nagyon hanyagoljak, szinte csak es kizarolag a speedbe fektetik minden eroforrasukat.
Igy mindkettovel rendelkezem., Amondo vagyok, hogy ilyen korrekt hozzaallas kellene az osszes szoftvergyartocegnek, legalabbis arazasban es a veglegesitett ideju licensz felteteleiben.
Ezert nem szeretem peldaul a virusirto szoftverek forgalmazoinak a lehuzo politikajat, ahol minden evben kulon fizetsz, mikozben nem veszel minden evben toluk masik szoftvert. Raadasul az arakkal is igen kizsakmanyoloan bannak.
A Cfos fejlesztoi ilyen teren magasan kiemelkednek a szememben.
Korrekt nem eltulzott aron adjak a termekuket es igy az is belefer a vegleges licensz miatt, hogy nem minden nap frissitenek, hanem tobb het vagy 1-2 honaponkent.
Jah, megéri, de már régóta ennyi az ára, karácsonykor asszem ennél is olcsóbb volt, aki még nem vette meg az ezután se fogja. :D
Amúgy arra jó ez a trial reset, hogy 10 nap után ne kezdje minden gép bekapcsoláskor/újraindításkor megnyitni az alapértelmezett böngészõt, hogy nagyon köszöni, hogy teszteljük...asszem régebben olyan volt, hogy még egy kis ablakot dobott fel elõtte, hogy 19 napom van hátra a tesztelésbõl és ha leokéztam akkor megnyitotta a böngészõt. Ez most vagy akkor jön elõ ha már csak 10 nap van hátra vagy kivették teljesen. Kár így erõsködni, úgyis megveszi aki akarja aki meg nem azzal mindegy mit csinálnak, akkor se fogja... :/
En meg a Cfosnal a beepitett tarcsazot. :D Amugy ADSL-hez jobb is a sima CFOS, mint a speed, ha nem hasznal a felhasznalo routert, mert akkor nem kell bridge mondban setupolni a modemet.
Am. nem a sebesség a lényeg hanem, hogy priorizálja az adatcsomagokat, pl. torrentezés közben vígan böngészhetsz vagy online gameknél leszoríthatja a pinget ezáltal. Néztem pingtestet és ha bekapcsolta az alacsony ping opciót akkor tényleg javított egy kicsit, nem hatalmasat de mérhetõ volt a javulás.
Lehet, hogy 8 vagy 15 megás net felett már nem kell, de minimális erõforrást használ és nekem az is tetszik, hogy jobb alsó sarokban látom ha adatforgalom van és azt is látom, hogy mekkora sebességgel. :)
Eddig 4 megás ADSL-em volt. Ez a gyakorlatban 460 / 26 Kbps le feltöltést tudott. Ennél soxor jól jött a C-fosspeed.
Az új netem nem ADSL. Stabil 6/2 megát tud. ( Ez sem egy nagy sebesség manapság, de a feltöltés 10 szerese a réginek. )
Szerintetek ennél a netnél érdemes a C-fosspeed-et használni, vagy itt már nincs értelme ? Most egy újratelepített winem van és nincs fenn rajta. Elég jól megy így is a net.
Ja, gondolom ez a hivatalos:D akkor ok. Nemsokára kipróbálom. Gyakorlatilag a pingem nagy az OnLive-hoz, a sebesség megvan, de ezzel a pinget akkor megnöveli.
Igen, pont jó lesz, és megbízható linket tud valaki adni? mert amit találtam megbízható helyrõl, az régebbi.
Üdv. Nem, ez arra jó, hogy stabilabb legyen a neted, pl. torrentezés mellett is simán és gyorsan tudjál böngészni vagy netes játékokban jobb legyen a pinged.
Üdv. Most ez a progi arra jó, hogy a külvilág azt higyje gyorsabb a neted? Mert emiatt nem enged fel OnLive-ra, csak nagyon ritkán, akkor viszont játszható.
Hol lehet a le és feltöltés lekorlátozni saját gépem bármely programjára ami kimegy a netre?
Sziasztok!
Szeretném megoldani 2 megás adsl netre 3 felé osztását fix korlátozással cfossped segítségével. Mind a 3 gépnek 85kb le - 4kb feltöltést adnám meg. (2 xp, 1 w7-es gép) Ezt hogy lehet egyszerûen megcsinálni? 5.12-es probaverzio van fennt.
Hát pedig @Narxis verziója tökéletesen mûködik;) amúgy a vírusírtók azért nézik vírusnak mert crack és mert van benne autorun de ezt már elmondta Narxis
10 víruskergetõ jelez rá, de azért mert ha automata módot választjuk akkor elindul a rendszerrel és minden windows indításnál aktiválódik.
Én kipróbáltam, feltettem az 5.12-es verziót, rátelepítettem az 5.10-re és kiírta, hogy 2 napom maradt tesztelni, elindítottam a trial resetet és most 30 napot ír ki.
Lecsereltem a CFost, Cfosspeedre es olyan hiba jelentkezett nalam, amit nem ertek. Amikor torrentezek szakaszosan valtozik a letoltesi sebessegem. Ahonnan mindig maximum speeddel szoktam tolteni, most azt tortenik, hogy felmegy a sebesseg maximumra, tolt ott 5-10 masodpercig majd leesik a speed 50k-ra 5-10 masodpercig majd megint felkuszik maximumra. Olyan mint amikor a buffert urittik. Valaki nem tud erre megoldast ? Mert ez igy nagyon gagyi, hogy maximalis letoltes helyett joval lassabban toltok le emiatt a hiba miatt.
Nem ugy mint a reginel, hogy a konyvtarban van egy key.cfos vagy milyen nevu fajl amit ha elinditasz feljon egy ablak ahol elfogadhatod a licenset es utana lehet beirni a serialt ?
Nincs valakinek ötlete, hogy az mitõl lehet, hogy ha a cfosspeed fent van és elindíto kegy torrentet max letöltési sebességgel (10 megás a net, de igazából ha 500-al tölt akkor is csinálja) akkor egész egyszerûen elkezd akadozni a hang, winampban szaggat az egész, játékok alatt szintén és a kép is beakad. Próbáltam az 5.0-t régebbit mindegyikkel ez van. Mit kellene állítani? Ja igen csak win 7 alatt. XP alatt semmi gond nincs.
Szia szokolof!
Próbáld meg azt, hogy eszközkezelõben kikeresed a hálókártya driveret és eltávolítod a jelenlegi illesztõprogramot, majd nem indítod újra, hanem felrakod a cfosspeedet és csak utána restart. De "a telepítés folytatása nem ajánlott" üzeneteknél mindig arra kell menni, hogy folytassa. Remélem ez segít.
Megvan a megoldás...:D Legalábbis nekem így sikerült.
cFosSpeed 5.00 build 1560 tiltott regisztrációs jelszóval való aktiválása:
00. Telepítsd fel a cFosSpeed-t! 01. Menj a "C:\Windows\System32\drivers\etc" mappába és a "hosts" fájlról csinálj biztonsági mentést (késõbb kelleni fog!!!), majd másold be felülírással a mellékeltet [Windows\System32\drivers\etc\hosts] 02. Telepítsd fel a "WWebserver" nevû programot [WWebserver 0.9.exe], majd másold a telepített program mappába a mellékelt "blacklist.txt" szövegfájlt [WWebserver\blacklist.txt]blacklist 03. Indítsd el a "WWebserver" nevû programot, majd kattints a "Start"ra 04. Most aktiválhatod a "cFosSpeed"t bármilyen tiltott, régebben mûködõ regisztrációs jelszóval!!! ;) :D :P 05. Miután sikeresen aktiváltad a "cFosSpeed"t lépj ki a "WWebserver" nevû programból (zárd be a tálcán levõ ikonnál is), majd távolítsd el [remove.exe]! 06. Rakd vissza az eredeti "hosts" fájlt (01. lépés)!!! 07. Indítsd újra a számítógépet!!! ;) :D :P
Jaj, ezek a németek...:) Egyébként a blacklist-nek nem az lenne a feladata,hgy ezt kikerülje? Esetleg crackelni nem lehet, vmiképp? Mint a Nodokat szokták örökös 30napos "próbaverzió"...?
Ráálltak a warez kulcsokra, hiába adja meg valaki, ha hirtelen sokan kezdik el használni akkor azonnal letiltják.